Show Posts
Pages: 1 ... 3 4 [5] 6 7 ... 15
61  Main Forum / Tips and Tricks / Re: Fixing rusted entry way on: May 29, 2014, 05:18:21 pm
Holly you are a Sweetheart,

I was able to print the exploded view to an .xps file  later I'll blow it up.

Thank You

John give her a big hug for me
62  Main Forum / Tips and Tricks / Re: Fixing rusted entry way on: May 29, 2014, 04:44:31 pm
Thanks Barry, I went out and looked at the screen door, I noticed a snap on plastic  cap on both top and bottom runners and two end caps on the tube.  Once I finish my re caulking job that is my next project.  I would like sand the whole area down and paint it with Chasis Saver, and then a coat white Rust O Leum. I believe Ron Dittmer did it this way.  Afterward I'll glue in some carpet pieces under the awning tools, or add carpet to the area held down with velcro strips for easy removal.

I did see in another post that gradygal (George) was thinking of adding rubber gasket onto the bottom of the entry door and removing the gasket piece just inside.  I would like to do that as well, the gasket is a dirt trapper and I'd like to see it gone.

Thanks again for the reply
Bill

63  Main Forum / Tips and Tricks / Re: Fixing rusted entry way on: May 29, 2014, 11:53:45 am
some rust is under the bottom of screen door
64  Main Forum / Tips and Tricks / Fixing rusted entry way on: May 29, 2014, 11:41:32 am
I am bout to tackle the rust around the bottom of the entry door. In earlier post I found some good answers to this problem. I am wondering if the screen door is removable.

Bill
65  Main Forum / Tips and Tricks / Re: Rust on interior of door frame on: May 27, 2014, 08:21:59 pm
I'm about to tackle the entry door rust problem.  Reading the posts made here most of my questions were answered. I am wondering if the screen door can be removed so that I can clean and repair the whole step at once.

Bill
66  Main Forum / Tips and Tricks / Re: MCD shades banging on window frame on: May 26, 2014, 09:17:00 am
We had the old shades replaced at the factory last year. The new MCD shades are much easier. I did add Velcro strips to them so when they are down they won't swing out over the bed, plus it stops the banging noise when driving.
We are very happy with the change
67  Main Forum / General Discussion / Re: New water heater installed on: May 23, 2014, 11:24:30 am
Posting this picture of the new water heater back and the pipe mentioned earlier. This pipe protrudes about 1.25 inches and was remove in order to put the cabinet back together

Bill ...

Have Nice Memorial Day Weekend .. Remember Those That Served ... And Our Men and Women Serving Today
68  Main Forum / General Discussion / Re: New water heater installed on: May 21, 2014, 03:43:38 pm
Yes it is Mike .... The installer told me that it is something that Winnebago came up with. And that this model is the unit used to replace the water in my 2008 2350
69  Main Forum / General Discussion / New water heater installed on: May 18, 2014, 07:40:42 am
Had my new water heater installed on Friday, now I have the chore of trying to put the cabinet back together.
The new Atwoods come with a pipe on the back that allows a hook up to the engine. This pipe has got to go, I  cannot  reassemble the cabinet wall with it there.  Hopefully it'll be done today. 

Must be ready to go, as we are for Wells Maine for the week.

Bill G
70  Main Forum / General Discussion / Re: wireless toad lights on: May 16, 2014, 09:09:45 am
Saw this on Facebook thought I'd share.

Bill G    pulling hair out
71  Main Forum / Adventure Anywhere / Re: Acadia national park on: May 09, 2014, 08:46:26 am
If you have time try and visit Jonesport Maine.
72  Main Forum / Polls / Re: Does your Phoenix Cruiser have a slide out? on: April 28, 2014, 07:11:58 pm
No
N/A
No
No
No surprise with Ron, right?
Like BGolden, I too would like a 2450 but it ain't gonna happen.  This baby's gotta last us.

Tom, You could set this up to do the "Pool Clicky Thing" so it tallies up the votes for you.  You want all to see at a glance that there is only one vote for a no-slide.   LOL

You got 2 no votes on the slide ..... Karen said " NO". There goes my 2450 Heart Shower
73  Main Forum / Polls / Re: Does your Phoenix Cruiser have a slide out? on: April 27, 2014, 03:13:19 pm
1. No

2. n/a

3. Yes

4. I want a 2450
74  Main Forum / General Discussion / Re: Removing refrigerator from 2551 on: April 24, 2014, 12:09:39 pm
Yes Tom Hanlon my fridge works the same way as your 3 way in the Chinook.  We do keep it on auto and for that reason it switched to DC  when the LP failed. Again this happened while we were driving when the LP failed.

The first year(2008) we had a problem with the LP, two service techs could not find the problem. It was one of those situations it worked or did not. Of course it worked for RV techs. In 2009 the problem began again on our way home from Branson. We pulled off in PA at an RV dealer that went through the whole thing and again could not find the problem.

Finally I called a guy that services at RV s at your home, he too was going nuts about it. After 1 hour he decided to pull the piezo out and took a look at it under a magnifying glass to see that was a small black dot. From this very annoying little black dot my piezo was arcing. We replaced the piezo and lived happily ever after.  I now have a magnifying glass in my tool box.

I kept that piezo for show and tell.

Thumbs up to you for your reply,
Bill Golden.       
75  Main Forum / General Discussion / Re: Removing refrigerator from 2551 on: April 24, 2014, 07:42:52 am
Tom and Ron,
I have used it on DC only when the unit switched over during the time when we were having problems keeping the LP lit. We did have to replace the piezo.

Ron, your dealer tried to talk me out of it as well, but I went ahead and bought it as a backup.
Forgetting that I did order it as an extra, my wife just reminded about that .

Beyond the ignitor, the fridge has done the job.

Bill
Pages: 1 ... 3 4 [5] 6 7 ... 15