Show Posts
Pages: 1 ... 8 9 [10] 11 12 13
136  Main Forum / General Discussion / Re: Kwikstep / Kwik-Lube on: October 26, 2011, 05:22:43 pm
Bob...

Great idea on the table!  I'll be in touch via email...All the best
Jack
137  Main Forum / General Discussion / Re: Kwikstep / Kwik-Lube on: October 22, 2011, 10:00:30 am
Thanks Bob --- just blew out the lines & antifreezed the drains --- don't know what we're doing over the winter --- going to PEI & NewFoundland this summer.
Would love to have you all here as well --- let me know if you do anything on the taable -- thanks.
Jack
138  Main Forum / General Discussion / Re: Kwikstep / Kwik-Lube on: October 21, 2011, 10:29:34 am
Semper Fi, Bob!!! Hope all is well with you guys--- Btw, dw decided she doesn't care about the drop down dinette table (not much length for a bed) so we won't be going to Elkhart --- If you change yours, let me know how Kermit did it, and how you like it..
Jack
139  Main Forum / General Discussion / Re: Hot Water tank bypass on: October 21, 2011, 10:10:33 am
Hey Tom --- I'll push the helpful button!!! I tried those d--- arrows every which way but the right way (both up, both down, etc.) -- BTw, I had to remove the panel (screws) on my 2006 2350 ---
When do you get your new baby?
Jack
140  Main Forum / General Discussion / Re: Kwikstep / Kwik-Lube on: October 19, 2011, 02:39:43 pm
As lmichael says, use a dry lube, and be careful on the drive screw under the slide --- I used white lithium grease on the old unit, and it spotted the rug when the slide retracted - just a word of caution.  I've been using Break Free on the step.
Jack
141  Main Forum / General Discussion / Re: Auto drain valves on: October 11, 2011, 05:21:38 pm
I had paper get lodged between the disc & seat of the black water tank, so the valve wouldn't seat. Disconnecting the drive fitting from the shaft was very easy, and after moving the shaft a few times, the paper cleared and valve seated.  I don't think you'll have any problem disconneting the drive, and moving the valve stem manually.  Once you move the shaft, a little lube might help.  I'd tryy this before taking the valve apart.
Jack
142  Main Forum / General Discussion / Re: QR Codes on: September 17, 2011, 12:17:58 pm
Aimee --- I think most everyone knows them, or at least will, soon --- most all of the catalogs and even our little newspaper in Queenstown has them.  However, because I, like others, am too cheap to add the data package to my cell, I don't use!!!

Best,
Jack
143  Main Forum / General Discussion / Re: Hershey RV show on: September 17, 2011, 12:02:56 pm
Tom --- GREAT SHOT!!! We went from the 2350 to the 2552 as well, and are very happy!!! Just returned from the owners ralley in NH without a hitch..and met lots of great folks to boot!  You'll be very happy...

Best,
Jack
144  Main Forum / Around the Campfire / Re: BEER, FISHING, GOLF AND SEX on: August 14, 2011, 04:21:14 pm
That's the best one yet, Billy!!!
145  Main Forum / General Discussion / Re: Water tank issues on: August 12, 2011, 09:35:57 am
I have one of the fill tubes as well --- makes a world of difference...

Jack
146  Main Forum / Tips and Tricks / Re: Macerator Rebuild kits? on: July 18, 2011, 05:18:13 pm
I finally bit the bullet and replaced mine --- got it from PC for less than Thetford wanted, and it was an easy job...
Jack
147  Main Forum / General Discussion / Re: Paint codes 2009 2400 PC on: July 14, 2011, 11:57:14 am
Will Kermit have the new changes and colors at the Owners rally?
Jack
148  Main Forum / General Discussion / Re: Tow bar alighnment on: July 13, 2011, 02:01:40 pm
I love it, Aimee!!!

Jack
149  Main Forum / General Discussion / Re: Price Negotiation on: July 07, 2011, 03:01:03 pm
Welcome, Tusocks!!!!  You'll be VERY happy with Phoenix, --- We are on our second, a 2552, after owning a 2350.  Looked at just about everything in the 23-25 foot range, in US & Canada, and came back to PC --- the product is just too good, many "standard" features are options on others, and the entire staff can't be beat.  If I ever decide on another RV, it'll be a Phoenix for sure.  As far as pricing, talk to Stuart --- he will be fair.
Good luck,

Jack
150  Main Forum / General Discussion / Re: (auto drain rocker arm switch) opens valve for macerator on: July 05, 2011, 11:58:55 am
Connie...your problem might well be the macerator --- try turning the screw on the beck of the pump (might have a rubber cover that needs to be removed) -- I've found this to be a remedy and don't have to mess with the wiring.  Often paper or something causes the macerator to stick, and turning the screw takes care of it.

I replaced the analog TV with a digital in my 2350 before I got the 2552...it was fairly easy as far as mounting.  However, because the dimensions are different, I had to add a piece of maple (the trim wood in that one) at the top.  It really didn't look too bad.  Unfortunately, I can't give you a picture, but you may be able to see it on the PC site under inventory --- the 2350 with "only 14K miles"  assuming they show a photo of the interior.  BTW, the replacement was a Samsung (same as the analog)...

Jack
Pages: 1 ... 8 9 [10] 11 12 13