Show Posts
Pages: 1 [2] 3 4 ... 8
16  Main Forum / General Discussion / Re: 2350 or ? What did you choose and why? on: July 29, 2012, 11:30:41 am
Best of luck with your search for a PC.  We have a 2011 PC- 2350 without a slide.  We felt the less moving things (slide) the less problems to worry about.  We are very happy with our choice.  We have one dog and keep a crate under the dining table.  When we travel he is in the crate.  It works for us.  Up to this point, we have not had a reason to use the dining area bed.
Please feel free to ask other questions.
Roni 
17  Main Forum / General Discussion / Re: A/C problem again on: July 10, 2012, 01:39:54 pm
To follow up, we just got back from our service place and the A/C is working fine.  First the tech ran it off the generator-everything fine.  Then plugged into electric with the 20 to 30 amp adaptor.  Again everything was fine.  He took the top off and checked everything from the roof end.  Also checked the connections from inside the RV.  He felt everything looked good and couldn't explain why we had had the problem.  He wanted to know if, when we had the problem, we had turned it off and tried again.  We had not done that.

We were never told not to run the A/C when at home with an adaptor going from 20 to 30 AMP.  Not sure I understand why that would be a problem.  It doesn't seem to use 20 AMPs.  We are due to "exercise" the generator.  So just to check it out again, we'll run the generator with the A/C.

18  Main Forum / General Discussion / Re: My 2350 got weigh today on: July 08, 2012, 07:58:24 pm
Denny & Barb,
I recently weighed my 2011 PC 2350 w/o slide at a CAT scale.  The front steer axle was 3180 lbs and the drive axle was 7820.  Gross weight was 11000.  Looking at the Michelin tire pressure chart, I also had a difficult time figuring out the correct pressure for the tires.  It does not seem to be an exact science.  I decided to go with 70 in all the tires.  So far, it seems to be working well for us.
Roni
19  Main Forum / General Discussion / A/C problem again on: July 08, 2012, 07:48:44 pm
Hi,
If you remember, while we were in Florida in April, we had a problem with the A/C.  Although it was cooling, after about 4 hrs, water was coming out of the A/C, running into the RV.  We had a mobile service check it out and whether it was too tight or too loose, nothing was found to be wrong.  It was then working fine. 
This past week we were in VT and it was working fine.  When we returned home, we plugged in to run the air while we were cleaning.  It was not cooling.  It was blowing warm air.  Also it would run for a few minutes and then cycle off. Within about 2 seconds it would kick back on.  Luckily, we are not currently camping.  We have an appointment to get it looked at on Tues.
I'll follow up with the forum after I find out what is wrong.
I did try to call the factory on Friday, but I think they have time off for the holiday.
Roni
20  Main Forum / Tips and Tricks / Re: Our 2910 Single slide on: July 07, 2012, 12:55:20 pm
Judi,
I also like the pull out draw instead of the cutting board.  For us, it would definitely be more functional.  We will pick one up when at Bed Bath and Beyond. 
Thanks for the great idea!
Roni
21  Main Forum / Adventure Anywhere / Re: Planning September Trip Michigan to Maine on: June 26, 2012, 09:27:32 am
Wild Duck in Scarborough, ME is very nice.  We were there last year and will be there again this Sept.  It is considered an adult campground in that it doesn't allow children.  It doesn't have a pool, no activities.  We really enjoyed the quiet!

We will be going to Boothbay Harbor, ME in August- staying at Shore Hills campground.  It gets very good reviews.
Roni
22  Main Forum / General Discussion / Re: surge protection on: June 07, 2012, 06:35:35 pm
I have the plug in Progressive Industries EMS-PT30C.  I am happy with it.

http://www.progressiveindustries.net/ems_pt30c.htm

Roni
23  Main Forum / General Discussion / Re: 2012 PC Brochure correction on: May 25, 2012, 06:24:43 pm
Wow- that is exciting!
Congratulations!
Roni
24  Main Forum / General Discussion / Re: Still here on: May 11, 2012, 04:28:07 pm
We also like the 2350.  Consider a good surge protector, water filter, different length water hoses.  We have both 15 and 25 feet, for the most part we use the shorter one.  We also have a tire monitoring system that we like. A coaxle cable  for cable hookup.  Also an assortment of tools as mentioned.    There are really good suggestions all over this forum.
25  Main Forum / General Discussion / Re: We're going to Elkhart on: May 10, 2012, 10:16:59 am
We are currently sitting in the factory waiting area.  Aside from getting the microwave and rear view mirror/camera replaced and our Sani- con valve light fixed, we have decided to change out our day/night shades to the MCD shades.  We are excited about getting every thing taken care of at once.  Everyone has been very nice.
26  Main Forum / General Discussion / Re: Floor mats on: May 09, 2012, 06:26:33 am
We have a 2011 PC 2350.  We finally decided to get them from Ford.  Certainly not the cheapest route, but they fit the configuration of the front area.  They still don't fit as well as we'd like.  We also put it right over the rug mats that came with it in the cab area. I would have liked them a bit larger.  The quality is good.  When I looked on line, it was difficult to figure if they would be cut out in the right configuration.
Good luck.
Roni
27  Main Forum / General Discussion / Re: Trip to Elkhart on: May 08, 2012, 09:30:40 am
Good luck with your purchase!
Roni
28  Main Forum / General Discussion / Re: We're going to Elkhart on: May 08, 2012, 09:29:14 am
Tom,
Although we has started onto the turnpike when I read your message, it has been very helpful.  We have changed our plans a bit.   We are planning to stop at West Branch state Park in Bristol, OH tonight and then on to Elkhart.  We are taking your suggestion for staying at Eby's.  The cleaner water helped us decide.  We don't mind the 1/2 hr drive to the factory.  Although the highway stops sound interesting, we have a very noise sensitive dog.  He and therefore us would not deal well with a lot of highway noise.  We are planning to stop overnight in Erie and Cooperstown on the way back home to Cape Cod.
We know we have made the right decision to have the work done at the factory.  We want to make sure the wiring for the replacement rear view camera is done correctly.  It will be 2 units instead of one.  This way the extra part will be positioned properly.  Also, the microwave will be replaced rather than fixed.
Thanks again for everyone's help!
Roni
29  Main Forum / General Discussion / Re: We're going to Elkhart on: May 07, 2012, 09:21:09 pm
Sue,
Thanks for the info on the water.  At this point I think we will stay 2 nights in Elkhart.  We feel more comfortable with full hookups, so we will stay at the campground.  We will bring drinking water for us and our dog.  Hanging out at the factory while the work is being done will be stressful for our dog, I think going back to the campground will be better for him that night.  Looks like we will then take 3 days to get home with overnight stops in Erie, Cooperstown and then home.
We will be happy to get our problems worked out at the factory.
Thanks for your input.
Roni
30  Main Forum / General Discussion / Re: We're going to Elkhart on: May 07, 2012, 04:43:22 pm
Judi,
We are not yet back home from our trip.  We are currently in Lancaster, Pa.  We are on our way home from FL.  We were going home and then going to figure out our trip to Elkhart.  After thinking about it, we realized it is closer to go from here.  We are now just trying to figure out our game plan.  So far we are stopping in Navarre, OH and then on to the Elkhart campground.  We have an appointment at Phoenix for Thurs and then will probably stay in Elkhart overnight and then head home.  We will probably take 3 or 4 nights to get back.  This was a quick change of plans for us. 

I will look into the Ohio service plazas.  Sounds interesting.
Roni
Pages: 1 [2] 3 4 ... 8