Pages: [1]   Go Down
Print
Author Topic: request from those with slide experience  (Read 522 times)
gradygal
SuperHero Member
******

Helpful Rating: 92
________
OwnPC: Yes
NewUsed: New
PurchDate: March 2012
Model: 2910
ModelYear: 2013
Slide: Yes
IntColor: cherry
ExtColor: slate gray full body paint
Location: Florida
________
Posts: 631


our 3rd PC--Custom 2910


View Profile
« on: July 15, 2012, 03:53:31 pm »


This is a request from those who have experience with slides. Since, this is the first slide that we have had, we need guidance  about maintenance recommendations.
Do you use slide supports?
How do you maintain the rubber seals?
Do you add insulation to the underside?
How do you keep out bugs, mice or toads? 

George
Logged

Judi and George Nicholson
Punta Gorda FL
Barry-Sue
SuperHero Member
******

Helpful Rating: 324
________
OwnPC: Yes
NewUsed: New
PurchDate: 10/17/11
Model: 2551
ModelYear: 2012
Slide: Yes
IntColor: Cherry
ExtColor: Classic Umber
Location: Michigan
________
Posts: 779


View Profile
« Reply #1 on: July 15, 2012, 05:51:18 pm »

George,

Quote
Do you use slide supports?
   
      No
Quote
How do you maintain the rubber seals?
     There are all kinds of products for rubber seals - and there are pros and cons to using them.  You should be good for the first year and I would call Kermit and ask his advice.
Quote
Do you add insulation to the underside?
      We do not use any insulation and have never found a need for it.  We notice no air flow going between the seals.  If we know of extremely bad weather we may bring the slide in.
Quote
How do you keep out bugs, mice or toads?
       We use a "NO SOLICITATION" sign and we have never had a problem.  rolling on the floor rolling on the floor   For real - since we store ours in a garage it has never been an issue.  But we have heard to use dryer sheets or real pepperment oil on cotton balls scattered throughout to keep the pesking critters away.  We have never had any entry through the slide while we are camping. 

       The only thing we do is make sure the slide stays in the middle of the opening.  There are rollers on each side of the slide and you should make sure the slide remains centered between those two rollers.  We noticed a little rubbing on our 2350 and called Kermit and he told us how to adjust the slide mechanism so as to recenter the slide.  Apparently one of the nuts and bolts on the slide mechanism loosened and caused our slide to shift a little.  Now when Sue is doing the hard job of pressing that button I go on the outside and let her know that the slide is in a good position.  We do this periodically just to check. 

Barry
Logged

Barry and Sue 
Current   2012 2551 w/Slide
Previous 2008 2350 w/Slide
billy
SuperHero Member
******

Helpful Rating: 72
________
OwnPC: Yes
NewUsed: New
PurchDate: Feb, 6 2011. Same day Packers won super bowl
Model: 3100
Slide: Yes
Location: Coarsegold, Ca. About 20-25 miles S/W Yosemite
________
Posts: 760


Best Friends


View Profile
« Reply #2 on: July 15, 2012, 08:26:37 pm »


This is a request from those who have experience with slides. Since, this is the first slide that we have had, we need guidance  about maintenance recommendations.
Do you use slide supports?
No, never have
How do you maintain the rubber seals?
Believe ti or not, Baby Powder
Do you add insulation to the underside?
No
How do you keep out bugs, mice or toads? 
Never had a problem with critters coming in thru the slide. When dad passed away he left me with 4 gallons of Chlordane, 88% prof, you cannot by that proof any more. I spray around my house, sheds, carports and under the PC, then all over the undercarriage. Hope all this stuff helps, billy

George
Logged

Insanity: Doing the same thing over and over and expecting different results.
TomHanlon
SuperHero Member
PCPC
*******

Helpful Rating: 190
________
OwnPC: Yes
NewUsed: New
PurchDate: 11/11/11
Model: 2552
ModelYear: 2012
Slide: Yes
IntColor: Cherry
ExtColor: full paint Cafe
Location: Maryland
________
Posts: 1095



View Profile
« Reply #3 on: July 16, 2012, 07:40:07 am »


This is a request from those who have experience with slides. Since, this is the first slide that we have had, we need guidance  about maintenance recommendations.
Do you use slide supports?
Never have and never had any problems with the slides.

How do you maintain the rubber seals?
I have used spray silicone on the rubber to help keep it flexible. It makes me feel like I am doing good if nothing else.

Do you add insulation to the underside?
No the walls, roof and floor already have insulation in them. The outer wall is the cut out from the PC wall.

How do you keep out bugs, mice or toads? 
Never been a problem.

Logged

Tom Hanlon
Current PC 2012 2552 Full paint Cafe
First PC 2010 2350 Full paint Umbra
Pages: [1]   Go Up
Print
 
Jump to: