Pages: [1]   Go Down
« previous next »
Print
Author Topic: Macerator dead  (Read 2001 times)
dickreid1
Hero Member
*****

Helpful Rating: 71
________
OwnPC: Yes
NewUsed: New
PurchDate: Feb. 2012
Model: 2910
ModelYear: 2012
Slide: Yes
Location: FL
________
Posts: 157


All 48 States, boarder Provinces and Maritimes


View Profile
« on: November 30, 2013, 07:12:38 pm »
This morning I was all set up to dump, switched on the macerator pump and nothing.  No hum. No click. Nothing.

Dumped the old fashoned way.

Ok, we are back home now. I will have time to trouble shoot.  Give me some ideas like: where is the fuse? Connector? How to clear jam? How to test the motor?

Thanks and happy thanksgiving.

Dick
Logged
yankeeflyer
Guest
« Reply #1 on: December 01, 2013, 06:43:47 am »
I just fixed,mine last month.First look behind the cabinet with the macerator switch is.You will have to crawl under the vehicle to access this,remove the two electrical spade connectors from the switch.With a small piece of electric wire,momentarily jump the two spade clips together.If the motor runs,then head to the auto parts store and buy a new switch.If you're close to me in Satsuma,Florida,I'd be happy to help you repair it.  Cheers
Logged
dickreid1
Hero Member
*****

Helpful Rating: 71
________
OwnPC: Yes
NewUsed: New
PurchDate: Feb. 2012
Model: 2910
ModelYear: 2012
Slide: Yes
Location: FL
________
Posts: 157


All 48 States, boarder Provinces and Maritimes


View Profile
« Reply #2 on: December 01, 2013, 09:03:40 am »
Good idea.  I will try it first.
Thanks for the offer, but Palm Beach County is too far from Satsuma to be practical.

Dick
Logged
yankeeflyer
Guest
« Reply #3 on: December 01, 2013, 01:38:02 pm »
Good Luck!! I'll be heading for the Keys on Dec 11th to escape the cold up here in northern Florida!! Wink
Logged
JackD
Hero Member
*****

Helpful Rating: 31
________
OwnPC: Yes
NewUsed: New
PurchDate: 2017 (latest)
Model: 2350 Sprinter
ModelYear: 2017
Slide: Yes
IntColor: Cherry
ExtColor: Greystone
Location: Delaware
________
Posts: 200


View Profile
« Reply #4 on: December 01, 2013, 05:43:18 pm »
Have you tried turning the screw in the back of the motor? Sometimes it gets jammed with paper, etc. And you need to turn it manually to get it started.
Logged
dickreid1
Hero Member
*****

Helpful Rating: 71
________
OwnPC: Yes
NewUsed: New
PurchDate: Feb. 2012
Model: 2910
ModelYear: 2012
Slide: Yes
Location: FL
________
Posts: 157


All 48 States, boarder Provinces and Maritimes


View Profile
« Reply #5 on: December 01, 2013, 07:33:11 pm »
Jack,

Like what you do with a garbage disposal I suppose.  I will check the back side for how to do this.
Thanks,

Dick
Logged
dickreid1
Hero Member
*****

Helpful Rating: 71
________
OwnPC: Yes
NewUsed: New
PurchDate: Feb. 2012
Model: 2910
ModelYear: 2012
Slide: Yes
Location: FL
________
Posts: 157


All 48 States, boarder Provinces and Maritimes


View Profile
« Reply #6 on: December 02, 2013, 12:53:29 pm »
OK. It's working now.  Switch was ok.  Removing the end cover and turning with a flat-blade screwdriver cleared whatever was in it. Good lesson. Thanks guys.
Logged
yankeeflyer
Guest
« Reply #7 on: December 02, 2013, 01:32:37 pm »
Easy Peasy!! ThumbsUp
Logged
JackD
Hero Member
*****

Helpful Rating: 31
________
OwnPC: Yes
NewUsed: New
PurchDate: 2017 (latest)
Model: 2350 Sprinter
ModelYear: 2017
Slide: Yes
IntColor: Cherry
ExtColor: Greystone
Location: Delaware
________
Posts: 200


View Profile
« Reply #8 on: December 02, 2013, 04:53:21 pm »
That's often the issue with them, and a lot easier than messing with wires!!!
Good luck & enjoy,
Jack
Logged
BarbRN
Hero Member
*****

Helpful Rating: 11
________
OwnPC: Yes
NewUsed: Used
PurchDate: May 25, 2013
Model: 2551
ModelYear: 2010
Slide: Yes
IntColor: beige
ExtColor: tan
Location: Florida
________
Posts: 134



View Profile
« Reply #9 on: December 02, 2013, 07:37:47 pm »
 ThumbsUp I love happy endings!
Logged
Pages: [1]   Go Up
Print
« previous next »
 
Jump to: