Pages: [1]   Go Down
Print
Author Topic: New 7-Pin Connector Location  (Read 261 times)
Pax
Hero Member
*****

Helpful Rating: 44
________
OwnPC: Yes
NewUsed: New
PurchDate: July
Model: 2552
ModelYear: 2014
Slide: Yes
IntColor: Sunlit / Cherry
ExtColor: Sunlit
Location: Northern California
________
Posts: 269



View Profile
« on: March 21, 2014, 05:30:37 pm »

Apparently, PC-USA has recently moved the location of the 7-pin connector on all new models.  It is now located next to the bottom left side of the license plate (you can see the location in the pictures of the PC's for sale in the 'Inventory' section of the website) From what I understand there have been issues with the old location in some situations where there were drainage 'gulleys', parking lot/gas station entrances that are elevated or depressed, etc.

Has anyone had any issues with the old location next to, but a little lower than, the receiver?  I would think it may be more of an issue with the longer 2910 or 3100?

  - Mike
Logged
TomHanlon
SuperHero Member
PCPC
*******

Helpful Rating: 183
________
OwnPC: Yes
NewUsed: New
PurchDate: 11/11/11
Model: 2552
ModelYear: 2012
Slide: Yes
IntColor: Cherry
ExtColor: full paint Cafe
Location: Maryland
________
Posts: 1065



View Profile
« Reply #1 on: March 21, 2014, 05:40:54 pm »

No problems here.  Grin
Logged

Tom Hanlon
Current PC 2012 2552 Full paint Cafe
First PC 2010 2350 Full paint Umbra
ron.dittmer
SuperHero Member
PCPC
*******

Helpful Rating: 177
________
OwnPC: Yes
NewUsed: New
PurchDate: June 2007
Model: 2350 Ford
ModelYear: 2007
Slide: No
IntColor: Cherry&Green
ExtColor: FullBody Gray
Location: Dundee, IL
________
Posts: 1935



View Profile WWW
« Reply #2 on: March 21, 2014, 11:12:09 pm »

No problem with our 2007 2350/E350.  When loaded up on trips, the rear end is slightly lower than a level rig yet we have never had a problem scraping anything.  Admittedly I do pay attention to exiting gas stations and such with an angular approach.  I considered installing rear air bags to give a little lift, but have been doing fine without.
« Last Edit: March 22, 2014, 10:44:51 am by ron.dittmer » Logged

Ron Dittmer (wife Irene) 2007 Model 2350 Without A Slideout
Our Rig Is Available For Viewing Any Time Of Year In Dundee, IL
Stored At Home In Our Heated Garage (Well-Lit & Warm Comfort In Winter)
KB9OMH
Sr. Member
****

Helpful Rating: 10
________
OwnPC: Yes
NewUsed: New
PurchDate: 3/26/13
Model: 3100
ModelYear: 2013
Slide: Yes
IntColor: Maple
ExtColor: Sterling
Location: IL
________
Posts: 53


View Profile
« Reply #3 on: March 21, 2014, 11:35:48 pm »

While on a trip to CA. ran into some deep curbing out of gas stations and bottom out. It bent the holder for the 7 pin plug and broke the housing for the plug, I moved it to the bumper next to the license plate. I also got a coaster for the hitch to keep it from scraping the ground on my 2013 3100

Jim
Logged
randallandchris
Full Member
***

Helpful Rating: 4
________
OwnPC: No
NewUsed: New
Model: None
Slide: No
Location: MI and FL
________
Posts: 22



View Profile
« Reply #4 on: March 22, 2014, 11:57:49 am »

eTrailer has big selection of skid rollers, should probably be standard on MHs with long overhangs.
Logged
dickreid1
Hero Member
*****

Helpful Rating: 38
________
OwnPC: Yes
NewUsed: New
PurchDate: Feb. 2012
Model: 2910
ModelYear: 2012
Slide: Yes
Location: FL
________
Posts: 103


All 48 States, boarder Provinces and Maritimes


View Profile
« Reply #5 on: March 22, 2014, 12:03:23 pm »

Yep,

Completely clobbered it last summer.
Logged
Pages: [1]   Go Up
Print
 
Jump to: