Pages: [1]   Go Down
Print
Author Topic: problems  (Read 797 times)
billy
SuperHero Member
******

Helpful Rating: 72
________
OwnPC: Yes
NewUsed: New
PurchDate: Feb, 6 2011. Same day Packers won super bowl
Model: 3100
Slide: Yes
Location: Coarsegold, Ca. About 20-25 miles S/W Yosemite
________
Posts: 760


Best Friends


View Profile
« on: May 16, 2011, 11:17:11 pm »

Having a problem with my electric step. It will not stay out. Close the door and it retracts. Checked the on/off switch, its OK. Anyone have any ideas? Im going to ass u me the on/off switch interrupts the door switch? Any ideas?
« Last Edit: May 16, 2011, 11:23:31 pm by billy » Logged

Insanity: Doing the same thing over and over and expecting different results.
ron.dittmer
SuperHero Member
PCPC
*******

Helpful Rating: 180
________
OwnPC: Yes
NewUsed: New
PurchDate: June 2007
Model: 2350 Ford
ModelYear: 2007
Slide: No
IntColor: Cherry&Green
ExtColor: FullBody Gray
Location: Dundee, IL
________
Posts: 2017



View Profile WWW
« Reply #1 on: May 17, 2011, 08:39:10 am »

The only thing I can think of is that your Ford ignition key hole up front is not completely positioned right with the key removed.  That always forces the step to fold up.  You know how some ignitions are sloppy enough that you can actually remove the key while the engine is running.  It might be a Ford problem, not a Phoenix problem.
Logged

Ron Dittmer (wife Irene) 2007 Model 2350 Without A Slideout
Our Rig Is Available For Viewing Any Time Of Year In Dundee, IL
Stored At Home In Our Heated Garage (Well-Lit & Warm Comfort In Winter)
gradygal
SuperHero Member
******

Helpful Rating: 92
________
OwnPC: Yes
NewUsed: New
PurchDate: March 2012
Model: 2910
ModelYear: 2013
Slide: Yes
IntColor: cherry
ExtColor: slate gray full body paint
Location: Florida
________
Posts: 631


our 3rd PC--Custom 2910


View Profile
« Reply #2 on: May 17, 2011, 01:12:00 pm »

Billy,
We had the same problem on our 2011 PC 2551. It turned out that the 5 Amp fuse had blown. The fuse is not in any fuse box. There are 4 fuses tucked behind the panel directly under the emergency brake release. To access the fuses, you remove the panel. In order to release the panel, there is a small plastic clip where the emergency brake cable goes through. You have to lift the cable and pull it toward the passenger side of the cab. You'll find wired in fuse holders that have rubber caps. Open the caps and check the fuses. Good luck. Hope this helps.

George
Logged

Judi and George Nicholson
Punta Gorda FL
billy
SuperHero Member
******

Helpful Rating: 72
________
OwnPC: Yes
NewUsed: New
PurchDate: Feb, 6 2011. Same day Packers won super bowl
Model: 3100
Slide: Yes
Location: Coarsegold, Ca. About 20-25 miles S/W Yosemite
________
Posts: 760


Best Friends


View Profile
« Reply #3 on: May 17, 2011, 02:13:47 pm »

God I love this forum. That was the fix George. I was in the middle of finding the 5 amp fuse and Kermit called with the same info.  Replaced the fuse and woooooopie. Thanks for the info George, billy    ThankYou ThankYou ThankYou
Logged

Insanity: Doing the same thing over and over and expecting different results.
ron.dittmer
SuperHero Member
PCPC
*******

Helpful Rating: 180
________
OwnPC: Yes
NewUsed: New
PurchDate: June 2007
Model: 2350 Ford
ModelYear: 2007
Slide: No
IntColor: Cherry&Green
ExtColor: FullBody Gray
Location: Dundee, IL
________
Posts: 2017



View Profile WWW
« Reply #4 on: May 17, 2011, 03:19:48 pm »

Good information!  Glad it was an easy fix.  Hopefully your fuse won't pop a 2nd time.
Logged

Ron Dittmer (wife Irene) 2007 Model 2350 Without A Slideout
Our Rig Is Available For Viewing Any Time Of Year In Dundee, IL
Stored At Home In Our Heated Garage (Well-Lit & Warm Comfort In Winter)
Pages: [1]   Go Up
Print
 
Jump to: